Showing results: 1396 - 1410 of 1675 items found.
-
Keystone Compliance
Keystone Compliance offers engineering services for standard and custom lightning transient immunity testing requirements and surge immunity testing requirements. Lightning testing can be completed in single-stroke, multiple-stroke and multiple-burst testing. Direct lightning testing is typically required for exterior aircraft systems. Indirect lightning testing is required for most aircraft electronics, both internal and external. Indirect lightning simulates secondary currents and voltages that travel through circuitry and cabling. The testing is also referred to as a surge immunity test.
-
SKU-015-01-PCIe -
Amfeltec Corp.
PCI Express Backplane was designed to support a variety of modern PCI Express board’s production testing and debugging. The backplane expands the Host computer into four x16 PCI Express slots via 10 ft. CAT7 data and 10-pin flat Power control cables. PCI Express Backplane and UUTs (unit under test – add-in PCI Express board) are powered by a standard ATX power supply connected to the backplane via 24 and 8 pin power connectors located on the backplane.
-
SART -
Aeromarine SRT Ltd
The Search and Rescue Radar Transponder as a part of GMDSS is a subject to annual test during radio survey. The annual testing of SART is recommended due to SOLAS regulation IV/15.8.The purpose of an annual testing is to determine that SART is operational as defined in appropriate performance standards for Survival Craft Radar Transponders for use in Search and Rescue Operations, IMO Resolution A.802 (19).Also Marine Orders require that a radar transponder must be inspected, tested and have its batteries replaced at intervals specified by its manufacturer.
-
Shanghai MCP Corp
Store characteristic curves and panel setting parameters. Programmable test conditions ,measured results PC stored. Three cursor measurement modes: point, line, window. Two cluster characteristic curves display simultaneouslyfor compare and pairing. Screen read outβ, gm, Vce, Ic, breakdown voltage, leakage current and other parameters . Repeat and single measurement. Self-checking function . 7 Inch high-resolution TFT color LCD. Standard interface: USB, RS232, LAN
-
ML4039E -
multiLane
The ML4039E is a fully featured 400G BERT that can be configured as a 4-channel PAM4 53 GBaud or 4-channel NRZ 28/53 Gbps lanes. Also half rates of 26GBd are supported in PAM mode. The transmitters Support all standard test patterns mandated by IEEE and OIF such as PRBS13Q, SSPRQ, PRBS31Q, etc… The user may also program the TX to output a user-defined pattern up to 131 kb long. The transmit power is adequate for testing up to 10 Km SMF links.
-
PGK 25 -
BAUR Prüf- und Messtechnik GmbH
Cable testing with the BAUR PGK 25. Cables must be tested in compliance with the national and international standards. This applies before the commissioning of new cable networks. The portable BAUR PGK 25 cable test device is used for DC voltage testing in low- and medium-voltage cables. It is characterised by its low weight of only 16.5 kg, by the easy operation and solid construction for onsite use.* Compact device for DC voltage testing with negative polarity* Continuously adjustable output voltage* Perfect for mobile use
-
FluidScan® 1000 Series -
Ametek Spectro Scientific
The FluidScan® 1000 series handheld Infrared oil analyzer provides direct quantitative measurement of a lubricant’s condition and plays an important role in Machine Condition Monitoring (MCM) for proactive and predictive maintenance in Reliability Management programs. It determines when oil needs to be serviced due to degradation of the oil chemistry or contamination by other fluids such as water or the wrong oil. It is compliant with ASTM D7889 “Standard Test Method for Field Determination of In-Service Fluid Properties Using IR Spectroscopy”.
-
AIM GmbH
AIM’s > ARINC 429 test, simulation, monitoring and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with multiple processors for real time bus protocol and application support, massive memory and IRIG-B time code encoder/decoder functions are standard. The latest versions also support avionics discrete I/O.
-
AIM GmbH
AIM’s AFDX®/ARINC664P7 test, simulation, monitoring and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with multiple processors for real time bus protocol and application support, massive memory and IRIG-B time code encoder/decoder functions are standard. Versions are available to support the Boeing specific ARINC664P7 extensions.
-
WIKA Alexander Wiegand SE & Co. KG
Pressure balances (often also referred to as mechanical dead-weight testers or primary standards) are the most accurate reference instruments for pressure. Their functional principle is based on the physical principle of pressure = force/area. Mass pieces placed on the top of a piston-cylinder system are the source of a precisely defined force. By producing a certain (counter) pressure inside the pressure balance an equilibrium is achieved: the mass pieces, including the free-running piston of the piston-cylinder system, are floating, which will lead to a very accurate pressure at the test port.
-
Extech RD300 -
Extech Instruments Corporation
The RD300 Refrigerant Leak Detector detects leakages from air-conditioning units and cooling systems. It's easy to use and is ideal for detecting leaks from air-conditioning units and cooling systems that use all standard refrigerants. The multi-colored LED light bar indicates the level of leaking refrigerant detected by the RD300. The built-in, bright LED convenience light located at the sensor tip illuminates dimly lit inspection areas. Complete with leak test bottle, 9V battery, and protective hard carrying case.
-
Extech USB200 -
Extech Instruments Corporation
The Extech’s USB200 monitors voltage, current, and charge capacity (mAh) to determine the quality and stability of chargers, power banks, and cables. It’s designed with a standard USB-A connector to plug into a device to be measured. It also has a USB input to test the quality of charging cables by observing the displayed current. The USB Power Monitor measures the output voltage, current, capacity and stability to prolong the charging equipment’s life cycle and memory stores up to 10 readings. Includes protective USB plug cover for storage.
-
SONOSCAN I -
SONOTEC GmbH
The SONOSCAN immersion transducers for Non-destructive Testing (NDT) are mainly used to test metals and plastics for the smallest material defects. For example, binding defects, welding defects or cracks and pores in metal parts can be detected. The powerful, robust ultrasonic probes can be connected to all common ultrasonic testing devices. Due to variable designs and sizes, the immersion probes guarantee optimal use. In addition to ultrasonic standard pobes, we also offer customized transducers according to your individual specifications.
-
Mirae Corporation
High-quality connection solutions for precise measuring, testing and examination. Whether low or medium voltage range, whether precise test runs or preventive measuring and testing: With an extensive portfolio of specific components and cables, Stäubli always ensures perfect and reliable contact between the measuring instrument and the points, objects and systems to be tested. In addition, we are a proven partner of leading manufacturers of measuring instruments in this field, for example for equipping them with high-quality sockets. Every product meets all quality and safety standards.
-
ZERA® WM3000I -
Powermetrix Systems
The current measuring comparator WM3000I is a high-precision device for comparing secondary outputs from a current transformer under test (or digital output of Electronic CTs or Digital CTs) with a reference signal supplied by a standard transformer primary. The resulting error value will be displayed as ratio error and phase error on the screen. The operation of the comparator will be performed via an integrated 10.1” capacitive touch screen or controlled by PC software. The WM3000I is compatible with existing systems, like Knopp, and exports a data output for active database systems.
